Associated-equipment 12-1012 Quick Guide User Manual download pdf

Battery Electrical System Analyser

(12-1012)

For testing all 12V automotive starting batteries

rated in CCA, DIN, IEC, JIS# and EN. Also for

testing vehicle Electric

al System.

Quick Start Guide

Caution: Never lay tools on the

battery top. You may short the

terminals together causing harm to

yourself, the tools or the battery.

Always follow Battery Council

International safety

recommendations.

Warning: Battery terminals contain

lead compounds which is

hazardous to our body if consumed.

Please wash your hand

immediately after handling.

LIMITED WARRANTY

This Battery Electrical System Analyser [12-1012] is

warranted to be free from defects in material and

workmanship for a period of 12 months from the date

of purchase and is subjected to the following terms

and conditions:

1. Within the warranty period, the manufacturer will

repair or replace, at their options, any defective

parts and return to the owner in good working

order.

2. Any repaired or replaced parts will be warranted

for the balance of the original warranty or 90 days

from the date of repair, whichever is longer.

3. Cost of delivery charges incurred for the repair of

the product (to and from the manufacturer) will be

borne by the owner.

4. The warranty covers only the defects arises as a

result of normal use and does not cover those

arise from:

• Unauthorized modification and repair

• Improper operation or misuse

• Accident or neglect such as dropping

onto hard surfaces.

• Contact with water, rain or extreme

humidity or heat.

• Physical damages such as cables

broken, surface cracks, etc.

Performing Battery Test while it is still in the car:

Vehicle that was running has to have its engine OFF

first and then switch ON the headlights for 30 seconds

to remove the surface charge. After the headlights

had switched OFF, let the battery rest for at least 1

minute to recover before testing commences.

The car engine and all other accessory loads must be

OFF during test in order to have an accurate result.

When attaching the analyser clips, make sure that the

battery posts were not oxidized or badly corroded.

Clean them first before clamping to it. Do not clamp

onto the steel bolts directly which may give inaccurate

and inconsistent results.

Testing on stand-alone batteries:

Clean the battery posts with a wire brush prior testing.

For side- post batteries, install stud adaptors. Do not

use steel bolts for better results.

1. Connect the tester clamps to the battery

posts, Red to the positive (+) terminal and

Black to the negative (-) terminal. Rock each

clamp back and forth for better contact.

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Quick Start Guide

1 Battery Electrical System Analyser (12-1012) For testing all 12V automotive starting batteries rated in CCA, DIN, IEC, JIS# and EN. Also for tes

Page 2

2 2. It will run through a self-test and when completed it displays the Main Menu as shown below: New: Clear Memory Clear the last tested r

Page 3

3 8. Select the rating system: CCA, DIN, EN, JIS#, IEC; according to the battery rating. If you cannot find its rating then select Unknown. 9. If

Page 4 - RESULTS:

4 Grounding Test 13. Pressing  key once will scroll down to the “Grounding Test” 14. Press key will proceed to the display as

Page 5

5 21. If the measured resistance reading has gone beyond the limits, then it will display the screen as follows: Note: The above indica

Page 6 - Alternator Test

6 29. During cranking when it detects that there is no drop in voltage, it will display the following screen: 30. To exit the program,

Page 7 - LOAD TEST

7 Fig.2 Testing with load at 2,000 RPM: This test is to check the alternator’s

Page 8

8 Operation: Engine Must be OFF. Locate battery. Clamp Tester. Clips to Battery [+]and [-] posts. Check battery Rating [CCA,EN HELP KE

Comments to this Manuals

No comments

Associated-equipment 12-1012 Quick Guide User Manual

Browse online or download User Manual for Equipment Associated-equipment 12-1012 Quick Guide. Associated Equipment 12-1012 Quick Guide User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Equipment Associated-equipment 12-1012 Quick Guide